Difference between revisions of "Documentation/UserGuide/Formatting"
(→Introduction) |
(→Direct format vs. styles) |
||
| Line 11: | Line 11: | ||
= Direct format vs. styles = | = Direct format vs. styles = | ||
| − | + | The simplest way to understand how styles work is through a text document, but the concept is valid for all Apache OpenOffice components. | |
| − | Suppose | + | Suppose we're writing a long document with many chapters, and each chapter contains several sub-levels. The chapter heading needs to be written in a particular sans serif font (like Liberation Sans, Arimo, Arial...), in bold, and at large size. The body text must be in a particular, and smaller, serif font (tinos, times, or others). |
| − | While it is possible to do that with direct formatting, | + | While it is possible to do that with direct formatting, two specific problems arise: one of consistency (used 14 point instead of 16 for a heading, forgot to use bold...) and, perhaps more problematic, one of ''maintenance''. If afterwards you decide to change the typeface, or its size, or the page margins...you'll need to do a lot of work. |
| − | + | Suppose that instead of setting "Liberation Sans, 16 point, bold, centered, five millimeters before the paragraph, three after..." we just use "Heading 1", and instead of "Liberation Serif, 11 points, justified..." we just use "Body text," having defined beforehand the specific parameters of "Heading 1" and "Body text." By separating the ''attributes'' applied to the text from the ''definition'' of those attributes the administration of documents becomes far easier. For example, to change the font used in the document we only need to modify the definition, not the document content, because that change in the definition will propagate without effort. | |
| − | + | Beyond this, styles provide a lot more that just consistency and easy administration. They permit the creation of an automatic table of contents and numbered chapters, while allowing a particular set of graphical elements that use one style to display the same line style, or colour, or associated text. Finally, styles can even be used to set the format of a particular cell on Calc. Depending on its content, such formatting is more easily done through styles than direct formatting. | |
| − | + | Styles can be "stored" on particular documents, called "Templates," that reuse the styles definitions. Defining styles is something that seldom needs to be done, but can be used a lot. | |
= Administration and edition of styles = | = Administration and edition of styles = | ||
Revision as of 22:39, 4 March 2013
Template:Documentation/DraftPage
Contents
Introduction
In Apache OpenOffice it is possible to work in two different ways: applying format directly through the use of menus and toolbars, or through the use of styles.
Direct formatting seems easier, but can be problematic on complex documents. Styles seem complex, but are a really powerful tool that's easy to use once you get used to them: let's see why
Direct format vs. styles
The simplest way to understand how styles work is through a text document, but the concept is valid for all Apache OpenOffice components.
Suppose we're writing a long document with many chapters, and each chapter contains several sub-levels. The chapter heading needs to be written in a particular sans serif font (like Liberation Sans, Arimo, Arial...), in bold, and at large size. The body text must be in a particular, and smaller, serif font (tinos, times, or others).
While it is possible to do that with direct formatting, two specific problems arise: one of consistency (used 14 point instead of 16 for a heading, forgot to use bold...) and, perhaps more problematic, one of maintenance. If afterwards you decide to change the typeface, or its size, or the page margins...you'll need to do a lot of work.
Suppose that instead of setting "Liberation Sans, 16 point, bold, centered, five millimeters before the paragraph, three after..." we just use "Heading 1", and instead of "Liberation Serif, 11 points, justified..." we just use "Body text," having defined beforehand the specific parameters of "Heading 1" and "Body text." By separating the attributes applied to the text from the definition of those attributes the administration of documents becomes far easier. For example, to change the font used in the document we only need to modify the definition, not the document content, because that change in the definition will propagate without effort.
Beyond this, styles provide a lot more that just consistency and easy administration. They permit the creation of an automatic table of contents and numbered chapters, while allowing a particular set of graphical elements that use one style to display the same line style, or colour, or associated text. Finally, styles can even be used to set the format of a particular cell on Calc. Depending on its content, such formatting is more easily done through styles than direct formatting.
Styles can be "stored" on particular documents, called "Templates," that reuse the styles definitions. Defining styles is something that seldom needs to be done, but can be used a lot.
Administration and edition of styles
Beside Math, all Apache OpenOffice components make use of styles. These styles have their differences with each component, differences that will be treated on the corresponding chapters, but the workflow is always the same: opening the Stylists with F11 or with Format → Styles and formatting it will be possible to modify an existing style or to create a new one with a simple right click. To apply one style to an element of a document, simply select that element and double click the desired style.
Templates
The immediate question after spending some time defining and modifying styles is how can I use these styles on a new document?
File → Templates → Save will save a copy of the current document as a template that we can use on a new document with New → Templates and documents → Templates and double clicking on the needed template.
It is possible to do one step more and set our preferred template as the default template: File → Templates → Organize, double click on "My Templates", select the needed template and opening the Commands button select "Set as Default Template" (this option is also available with doing a right click on the template on the list).
To modify an existing template, with File → Templates → Edit and browsing to the template file, or File → Templates → Organize → My Templates and selecting Edit under Commands .
Once the changes are ready, it is enough to save the document as a normal document.
